KitchenAid Dryer Repair

Do you have a KitchenAid dryer that's acting up? Dealing with wet clothes is frustrating, especially when you've got other things to do.

We've seen just about every problem these machines can have. While some folks like to tackle repairs themselves, calling our service team is the safest bet for getting things fixed right the first time.

Let's go through common issues these machines have so you understand what's happening before we come out.

When Your Dryer Won't Start

Nothing happening when you push the buttons? It’s probably an electrical failure.

• First off, check your breaker box. Sometimes those things trip and don't even look different. Just flip it off and back on to make sure. And make sure it's plugged in good. Can't tell you how many appliance repair calls we've gone on where somebody bumped the plug while cleaning or something.

• The door switch is another common problem spot. These dryers won't run if that switch doesn't think the door is shut. Give the door a good close and listen for a click. No click? Might be a bad switch. This requires opening up the dryer and working with electrical components. While some homeowners try this themselves, our dryer technician has the right tools and parts to test and replace these switches quickly and safely.

• Sometimes the start switch has gone bad. Push the button and nothing? Not even a click or hum? Probably the switch is worn out. Could be the control board too. These repairs involve electrical components and precise installation. Something you can certainly attempt, but our appliance repair team handles these issues every day with the exact replacement parts your model needs.

Dryer Runs But Won't Heat

We see this one all the time. Motor's going, drum's turning, but clothes coming out cold and wet. A few common things usually cause this.

• Check your house electrical first. Electric dryers need 240 volts to heat right. If just one leg of your electric is working, motor runs but heating element stays cold. Make sure both breakers for the dryer are on.

• Breakers good? You’re probably looking at a bad heating element then. They burn out after years of service. Located behind the back panel. This repair requires working with high-voltage components and precise reassembly. While determined DIYers sometimes tackle this, our techs bring the exact replacement part for your model and ensure everything's connected properly to prevent future issues.

• Could be a blown thermal fuse too. These are safety things that blow when the dryer gets too hot. Once they're gone, you have to replace them - they don't reset. Replacing these requires knowing exactly which fuse your model uses and proper installation to prevent fire hazards. Our service team carries all the right parts and tests the entire system to make sure there isn't an underlying issue that caused the fuse to blow in the first place.

• High-limit thermostat can cause no-heat too. Another safety device that cuts power to the heater if things get too hot. Unlike the fuse though, this one usually resets itself after cooling down. Sometimes they go bad and stay open. When you call our dryer technician, we'll check all these components as part of our diagnostic process to find exactly what's causing your problem.

• Do you have a gas dryer? The problem could be the igniter, flame sensor, or gas valve coils. These gas components require special knowledge and tools to service safely. This is definitely a job for our professional techs who are certified to work on gas appliances.

Noisy Operation

Does your dryer sound like you're tumbling rocks in there? You’ve likely got some worn parts.

• Check the drum rollers and bearings. They wear out and start rumbling or squeaking. Requires taking apart much of the dryer to access and replace. Our techs come prepared with the right parts for your specific model and have the tools to complete this repair quickly.

• The idler pulley makes a high squeal when it's going bad. That's the pulley keeping tension on the belt. Don't waste time with WD-40 - needs replacement if it's making noise or feels wobbly. Getting to this component and installing it correctly takes experience. Our service team does these repairs daily.

• The blower wheel sometimes comes loose from the motor shaft. Maybe something stuck in there too. Makes a scraping or thumping sound. Accessing this requires significant disassembly. We bring specialized tools to secure these components properly.

• A rattling noise might just be something stuck in the drum baffle. We’ve found all kinds of stuff in there over the years. Coins. Paper clips. Kids toys. Something you might check yourself before calling, but if it requires taking things apart, it’s better to have us do it right.

Dryer Takes Too Long to Dry Clothes

Running forever but clothes still damp? Almost always airflow problems. These KitchenAid dryers need good air movement to dry properly.

• Lint filter first. Even looks clean? Run water over it. Water beads up instead of going through? Got fabric softener buildup clogging the mesh. Wash it with warm soapy water and a brush.

• Check the vent hose and outside vent too. Take the hose off the back and look for lint inside. Check where it comes out of your house too. Birds love making nests in dryer vents. Lint piles up over time. If you're comfortable checking these areas yourself, go ahead, but our service includes a complete vent inspection and cleaning. We have specialized tools to clean deep into vents where household tools can't reach.

• The vent hose itself could be the problem. Those accordion-style flexible ones restrict airflow way more than smooth metal ones. Crushed or kinked? We can replace it with the right type during our service visit to maximize your dryer's efficiency.

• A real long vent system slows drying too. Too many turns. KitchenAid says keep the duct under 25 feet. Each 90-degree turn counts as 5 feet. Our techs can evaluate your whole vent system and recommend the best solutions based on your home's setup.

Don't jam too many clothes in there either. They need room to tumble so air hits all surfaces. Stuffing it too full makes even a perfect dryer take forever.

Dryer Stops Mid-Cycle

Does your dryer quit in the middle of drying? Annoying. Usually means something is overheating.

• Most common reason is plugged up venting, just like with slow drying. Check all that venting stuff we talked about earlier. Clogged vent makes the dryer overheat, then the thermal fuse or cycling thermostat shuts it down for safety. When our service team comes out, we'll do a complete vent system check as part of our diagnostic process.

• Could be a bad cycling thermostat. That's what controls temperature during normal running. Not working right? Your dryer might get too hot and shut down. This requires testing with specialized equipment and knowledge of exactly which replacement part your model needs. Our appliance repair techs come prepared with these components.

• Motor thermal overload trips when it works too hard sometimes. Happens with heavy unbalanced loads or if the drum isn't turning easily. Our comprehensive service checks all mechanical components to identify these issues.

• The timer motor or electronic control board might be a problem too. It’s often had to figure out without proper testing gear. These complex components require expert diagnosis and precise installation. Definitely a job for our service professionals.

Dryer Too Hot

Clothes coming out scorched? Does your dryer feel super hot when you touch it? You’ve got a temperature problem.

• Check the cycling thermostat first. It controls heater temperature during operation. If the thermostat is stuck closed, the heating element stays on too long. This is definitely a safety issue that requires proper testing and replacement with the exact part for your model. Our techs carry these components and test the entire system after installation.

• Air flow could be partly blocked. Enough air getting through to prevent shutdown, but not enough to keep temperature normal. Our service includes a complete check of your vent system and dryer components.

• Some electronic control boards cause temperature problems too. If the control is not cycling the heat right, your dryer runs too hot. Not common but happens in newer electronic models. Diagnosing and replacing these specialized parts is best left to our factory-trained technicians.

Make sure you're using the right cycle too. That "high heat" setting on KitchenAid dryers gets really hot. Not meant for delicate stuff.

Drum Won't Turn

Powers on but drum doesn't spin? You're often looking at a belt or motor problem.

• The drive belt is the most common failure. They wear out eventually and break. Getting a new belt installed correctly is trickier than it looks. The belt routing has to be exactly right or it'll wear out again quickly or won’t spin the drum. Our techs know precisely how to route belts for your specific model.

• Belt looks good? Might be the motor. Listen carefully when you start the dryer. Hear humming but no movement? Motor might be trying to run but can't. Worn motor bearings or failed capacitor on some models cause this. Motor replacement is definitely a job for our professionals. We bring the exact replacement motor your model needs.

• The door switch might be broken. Our comprehensive diagnostic process checks all electrical components to identify the exact issue.

• The idler pulley or tensioner could be seized up too. This prevents the belt from moving even if everything else works. Our techs replace these components regularly and know exactly what your model requires.

Burning Smell

Burning smell from the dryer isn't normal. You need to handle this issue right away. Turn off the dryer and unplug its power cord until our service team can inspect it.

• Usually burning smell is caused by lint buildup where it shouldn't be. Lint gets past the filter into the cabinet, near the heating element or gas burner. When it gets hot enough, it starts to smell like burning. This is a serious fire hazard. Call our service team immediately for a thorough cleaning and inspection.

• A slipping or burning belt causes a rubber burning smell. Drum hard to turn or belt worn and slipping on pulleys? Creates friction and heat. Our techs will replace the belt and check for any damage to related components.

• Worn bearings in the motor or idler pulley overheat sometimes. Smell like burning too. These mechanical issues require proper diagnosis and repairs by our experienced technicians.

• Sometimes stuff gets into the blower housing or under the drum. It rubs against moving parts and makes burning smells from friction. Our service team will do a complete inspection to find any foreign objects or damaged components.

Why Call Our Service Team

While you might be tempted to complete some dryer repairs on you own, our professional dryer services offer several advantages:

• We always attempt to bring the exact replacement parts for your specific model, eliminating guesswork and multiple trips to your home.

• Our techs are factory-trained on KitchenAid dryers and know all the model-specific quirks and repair techniques.

• We have specialized diagnostic equipment to pinpoint problems quickly and accurately.

• Our service includes a complete check of the entire dryer, often catching developing issues before they cause breakdowns.

• We guarantee our work and parts, giving you peace of mind.

• Gas dryer repairs require certified technicians for safety and code compliance.

• Complex electronic components in newer models need expert handling to prevent damage.

When you consider the time, frustration, and potential for additional damage from DIY attempts, our professional service is the smart choice for reliable, long-lasting repairs.

Keeping Your Dryer Running Right

A few simple maintenance procedures prevent most common dryer problems.

• Clean lint filter after every load. This makes a huge difference in how the dryer runs and appliance safety too.

• Schedule regular professional appliance maintenance with our service team. We'll clean areas you can't reach and check for developing problems before they cause breakdowns.

• Don't slam the door. This damages the door switch over time.

• Keep the area around the dryer clear. This makes sure air flows good and cuts down fire risk.

Listen for changes in dryer sounds. When you notice something different, call our service team early. Catching problems early usually means easier, cheaper fixes.

Take care of your KitchenAid dryer and call our service team at the first sign of trouble. We'll keep your laundry routine running smoothly with expert repairs and maintenance you can trust.