How Does a Pressure Switch Work?
Your washing machine is an incredibly convenient appliance, transforming loads of dirty laundry into fresh, clean clothes with just the touch of some buttons. But to work effectively, the washing machine needs precise control over its water levels to avoid overflows or inadequate filling. This is where the water level pressure switch comes into play.
KEY TAKEAWAYS
- The water level pressure switch uses air pressure to detect and regulate washer water levels by sensing air pressure in an attached tube as the tub fills, signaling the control board to stop water intake once the correct level is reached.
- By controlling water intake accurately, the pressure switch ensures the right balance for effective cleaning and prevents water waste -- saving energy and resources.
- Regularly inspecting the air tube, checking for clogs, and following recommended load sizes can prevent problems like water overflows or insufficient water levels -- keeping the switch and washing machine in optimal condition.
The pressure switch regulates the amount of water in the tub, ensuring each cycle runs smoothly and efficiently. In this article, we’ll take a closer look at how the water level pressure switch works, why it’s essential, and how it impacts your washing machine’s performance.
What is a Water Level Pressure Switch?
The water level pressure switch is a small but critical part of a washing machine’s control system. It senses the water level in the washer tub and sends signals to the machine’s control board, dictating whether it should stop or continue filling the tub. This sensor is typically a small round component located inside the machine, with a long, thin air tube connected to the bottom of the washer tub.
The pressure switch serves as the washing machine’s “eyes” on the water level, ensuring the machine uses just the right amount of water for each load. Using too much or too little water can affect washing efficiency, so the pressure switch helps maintain the correct balance.
How Does a Pressure Switch Work?
The water level pressure switch works by detecting the air pressure changes in the washer’s air tube as water fills the tub. Here’s a breakdown of the process:
- Air Tube Connection: The water level pressure switch is connected to the bottom of the washer tub by an air tube. As the tub fills with water, it compresses the air inside this tube.
- Air Pressure Build-Up Moves the Pressure Switch Diaphragm: As more water enters the tub, the air in the tube gets more compressed, increasing the air pressure within the tube. The air pressure pushes up on the sensing diaphram inside the pressure switch.
- Pressure Switch Activation: When the air pressure reaches a certain point to indicate the tub is full, it pushes the diaphragm up against an electrical switch contact that stops the filling process by shutting off electrical current to the water fill valves. This pressure level is calibrated to correspond with the desired water level for the washer.
- Signaling the Control Board: When the washer has an electronic control board, once the switch detects the appropriate pressure, it sends a signal to the washing machine’s control board to stop filling the tub.
- The Pressure Switch Resets During the Drain Process: The switch remains in a “closed” position while the machine continues with the wash cycle. It then resets during the drain routine for the next water fill.
This air-pressure system is both accurate and reliable, helping the machine avoid underfilling or overfilling the tub.
Types of Water Level Pressure Switches
Different washing machines use various types of water level pressure switches depending on their design. Here are the common types:
- Mechanical Pressure Switches: These use a physical diaphragm that moves when air pressure builds up. This movement opens or closes electrical contacts, sending signals to the control board.
- Electronic Pressure Sensors: Some modern washing machines use electronic sensors that measure air pressure with more precision, providing more accurate water level control. An electronic washer water level pressure sensor (also called a water level pressure transducer) works in a similar manner to a water level pressure sensor but a transducer creates an electronic signal instead of activating an internal switch in the component. As the washer fills with water, air in the sensor air tube pushes up on the diaphragm and moves a rod or piston inside of a core in the transducer to create an electronic signal that is sensed by the control board to control water level in the washer tub. The electronic control board stops filling the washer and advances to the wash cycle when it senses that the washer tub is full based on the signal from the water level pressure transducer.
- Variable Water Level Sensors: These are designed for machines with multiple water level settings. They can detect specific pressure changes, enabling various levels based on load size and cycle type.
Regardless of the type, each switch follows the same general principle of measuring air pressure to control water levels accurately.
Why is the Water Level Pressure Switch Important?
The water level pressure switch is essential for multiple reasons:
- Prevents Overflows: By stopping water intake at the correct level, the pressure switch helps prevent overflows and potential water damage.
- Saves Water and Energy: The switch ensures the washing machine only uses the amount of water necessary for each load, conserving water and energy.
- Enhances Cleaning Efficiency: Correct water levels are crucial for optimal washing performance. Too little water can lead to ineffective cleaning, while too much water can dilute detergent, reducing its effectiveness.
- Protects the Machine: The pressure switch prevents excess water from entering the tub, which could strain internal components, such as the motor, or cause electrical issues.
Understanding the role of the pressure switch can help you recognize the importance of water levels in achieving clean, well-rinsed laundry.
Troubleshooting Water Level Pressure Switch Issues
Symptoms of a Faulty Pressure Switch
If the pressure switch malfunctions, you might encounter a few noticeable issues. Here are some signs that the water level pressure switch may be faulty:
- Overflowing Tub: If the switch fails to signal the control board, the tub may overfill, leading to potential spills and flooding.
- Insufficient Water Level: A malfunctioning switch might also prematurely signal the machine to stop filling, leading to lower-than-required water levels and ineffective washing.
- Error Codes on Digital Machines: Many newer washing machines have error codes that will display on the control panel if the water level pressure switch isn’t functioning correctly.
How to Troubleshoot Pressure Switch Problems
Here are some practical troubleshooting steps that you can take when you notice pressure switch problems in your washer.
Check the Air Tube
Over time, the air tube can become kinked or clogged, preventing the pressure from building up properly. It can also get cracked or damaged. Inspect the air tube for any obstructions or signs of leaks or damage. Make sure it’s properly connected to the pressure switch and the bottom of the washer tub.
Inspect the Switch
If you’re comfortable with attempting safe DIY repairs, unplug the washer and open the console or the top panel of the washer to access the pressure switch. Check the wire harness connections on the pressure switch and control. Reconnect any loose wires harness connection and repair any broken or damaged wires.
Here’s a helpful DIY video that shows how to fix damaged wires:
If the wiring connections are okay and you’re advanced DIY’er, you can find the tech sheet for your washer and use the diagnostic tests recommended in that document to safely test the internal contacts of the pressure switch.
If you’re unable to find and fix the pressure switch problem yourself, schedule washer repair service and we’ll send a Sears Home Services technician to your home to fix the issue.
Consult the Manual or Error Code Charts
For modern machines, the owner’s manual will often have troubleshooting tips or diagnostic modes to help you identify problems related to the pressure switch. If you don’t find the help you need in the owner’s manual, use our washer error code charts to interpret the code and follow the troubleshooting recommended in the chart to fix the problem.
When you’re unable to fix a problem causing an error code on your own, schedule washer repair and we’ll send a Sears Home Services technician to your home to fix the problem.
Maintaining the Water Level Pressure Switch
To ensure your washing machine’s pressure switch remains in good condition, follow these washer maintenance tips:
- Regularly Clean the Washer Tub: Debris buildup inside the tub can eventually clog the air tube or interfere with the pressure switch’s accuracy.
- Inspect the Air Tube Periodically: Check for cracks, kinks, or blockages in the air tube and replace it if necessary.
- Don’t Overload the Washer: Overloading the washer can strain the water control system and impact the switch’s effectiveness over time.
- Schedule Annual Professional Maintenance: Annual professional washer maintenance will help keep the pressure switch and your entire washer working efficiently. Professional maintenance will also help prevent unexpected failures and your washer will last longer when professionally maintained.
The water level pressure switch may be a small component, but its role in washing machine operation is crucial. This sensor ensures that each cycle uses the correct water amount, maintaining both efficiency and performance.
By understanding how the pressure switch works and how to troubleshoot potential issues, you can help extend the life of your washing machine and keep it running smoothly.
Whether you’re a DIY enthusiast or just curious about how your washing machine works, knowing the basics of the water level pressure switch is valuable for better appliance care and troubleshooting.
Schedule washer maintenance now!
Increase the lifespan and performance of your washer with our comprehensive maintenance service, ensuring reliable laundry care and continued peace of mind.
Was this information helpful?
Schedule washer maintenance now!
Maintain Washer Resources
Learn how a high-efficiency washer works and how to maintain it effectively.
Learn how portable washing machines work and how to use and maintain them properly.
Learn how the fabric softener dispenser works and how to keep it working right.
Learn how a washer works and how to keep it working efficiently.
Glossary Terms
Hard water is water that contains high levels of dissolved minerals, particularly calcium and magnesium. It contrasts with soft water, which has lower concentrations of these minerals.
A washing machine pedestal is a platform that raises the washer off the ground, providing easier access to the appliances and often includes additional storage space such as drawers.
A washer tub is the interior part of a washing machine where clothes are placed for washing, typically made of stainless steel, plastic, or porcelain-coated metal, designed to hold water and withstand the agitation or spinning during the wash cycle.
Fabric softener is a laundry additive used to soften and freshen clothing, reduce static cling, and make fabrics feel smoother.
Common Repair Washer Symptoms
The most common reasons your Whirlpool washer won't stop filling are a clogged water valve, a bad water-level pressure switch, or a malfunctioning electronic control board.
The most common reasons your Whirlpool washer won't spin or drain are a seized gearcase, a broken motor, or a failed door switch.
The most common reasons your Whirlpool washer won't turn off are a malfunctioning electronic control board, broken motor or a jammed door lock assembly.
The most common reasons your Whirlpool washer won't start cycle are a malfunctioning electronic control board, jammed door lock assembly or a faulty user interface.
The most common reasons your Whirlpool washer vibrates are a damaged suspension rod, malfunctioning electronic control board or a dead fan.
The most common reasons your Whirlpool washer is experiencing the rinse cycle not working are a broken lid switch, a bad water-level pressure switch, or a malfunctioning electronic control board.