Admiral dryer not drying

What to expect when you experience an Admiral dryer not drying issue

How is the not drying problem fixed?

Correcting most not drying problems usually involves replacing the vent tube, heating element or wire connector. However, there are many potential causes, so a thorough diagnosis is key to fixing the problem. An accurate diagnosis is essential to understanding how much the repair will be.

Sears Home Services recommendations for a dryer that is not drying

When the dryer is not drying it can be for many reasons. To avoid replacing unneeded parts we recommend having a Sears Home Services professional perform diagnostic tests to identify the root cause of the problem. Our technicians are experienced at diagnosing all types of dryer failures.

What to look out for with a dryer not drying diagnosis

Diagnosing modern appliances without proper knowledge and training can be difficult. Without using proper diagnostic techniques, fixing your dryer problem will only be achieved through changing parts on a hunch. Appliances, especially in the last 10 years, have become extremely advanced, and many models have electronic parts that are difficult to test. DIY repairs on the latest appliance models are becoming increasingly difficult.

Why is my Admiral dryer not drying?

Heating problems are a leading cause of a dryer not drying clothes. Also a clogged exhaust vent duct system can also prevent the dryer from drying clothes.

Check the exhaust vent duct system going to the outside of your home and clean out any lint clogs that you find. Make sure the damper vent on the outside of your home is opening properly.

If you don’t find any exhaust vent duct system problem, troubleshoot the heating system in your dryer.

Why is my Gas Dryer Not Heating?

There are a many things that could keep your dryer from heating up. You might have a problem with the gas supply to the dryer, or problems with the flame sensor, gas valve coils, high-limit thermostat, operating thermostat, thermal cut-off fuse, thermal fuse, igniter or timer. I know that sounds like a lot, but don’t worry, we’ll help you work through it with the troubleshooting tips in this video:

Once you find the cause of the heating failure, decide whether you want to fix the problem yourself or have a Sears Home Services technician fix the dryer for you.

Resolving a heating problem in your dryer with fix the appliance so it dries your clothes properly again.

Why Won’t My Electric Dryer Heat?

In this helpful DIY video, we show you how to troubleshoot your dryer that won’t heat, including checking the heating element, high-limit thermostat, operating thermostat, thermal cut-off fuse and timer. Learn about a few easy tests you can run to find the problem, including using a multimeter to make sure current is flowing between the parts. Once you know what the issue is, you can fix the issue yourself or have our Sears Home Services technician fix the problem for you.

Check the Power Supply

The first step is to check to see if the dryer is getting the correct amount of power. You may think the dryer is getting enough power if the motor runs, but the heating element needs 240 volts of electricity to heat. The motor will run even if the dryer is only getting 120 volts of power.

Check your power cord to make sure it’s not damaged. Then, reset your house circuit breaker to make sure it’s not tripped. Set your dryer to a timed dry, high-heat cycle and see if it heats up after resetting the breakers.

If it’s still not heating, you’ll need to check the components on the control circuit. Checking continuity with a multimeter will allow you to test them all at once.

First, unplug the dryer. For safety, always disconnect power before checking continuity. Remove the back panel from the dryer, then remove the back of the control panel. Unplug the large red wire from terminal "A" on the timer. Set the multimeter to read ohms of resistance.

Measure resistance between the large red wire on the timer and the heating element terminal where the large red wire is connected. If you measure near 15 ohms of resistance through this circuit, then you know that the heating element, high-limit thermostat, operating thermostat and thermal cut-off fuse are all okay. You can skip ahead to learn how to check out your timer in the video.

Check the Dryer Heating Element

If you measured no electrical continuity through the circuit described, then check the heating element. Place your meter leads on the heating element terminals. You should measure near 15 ohms of resistance through the heating element.

If you measured no continuity, then the heating element is broken. This video will show you how to replace it:

If you measured near 15 ohms of resistance, then the heating element is good. Continue with the troubleshooting tips in the video to find the cause of your dryer not heating and not drying clothes properly.

When your Admiral dryer tumbles but clothes remain damp, airflow restrictions or broken heating elements may be the cause. Simple vent cleanings might solve partial issues, but stubborn failures need advanced care. Book a dryer repair near me visit for thorough diagnostics. You’ll save time, energy, and frustration.